pailsled73

How to Replace a Kia Sportage Replacement Key The key on many Kia models comes with an entry system that is keyless into. The key is usually akin to a remote control and can be changed by a new one purchased from an Kia dealer or locksmith. Key fobs can stop working due to a variety of reasons, including an inactive battery, worn out buttons signals, signal interference or water damage. Here are some suggestions on how to get your Kia Sportage replacement key back to working. How do you replace the remote key or smart key The battery in your Kia's intelligent key will eventually need to be replaced, whether it's a remote key, a push-to-start key or a regular metal key that doesn't contain an electronic transponder. This is particularly when your car displays a message that indicates the smart or remote keys aren't powered. Fortunately, it's an easy procedure. To replace the battery of the key fob remove the mechanical key from the slit in the back of the key fob. Then lift the cover. A small screw will be found inside the key fob that holds the battery in place. Remove the old battery by unwinding the screw with a small screwdriver. Then, you can insert the new battery and close the slit in the key fob. Test the key fob by pressing the lock/unlock buttons. It's okay in case the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you have to complete errands in Brandon. Note: Certain key fobs (transponder chip or smart keys) might require their programming done. This requires a machine for programming, which is only available to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of steel) are not required for programming. If your key needs to be reprogrammed, you must be aware of the key code number that is stamped on the tag that identifies the key and record it in a safe place. How do you replace the battery? If the Kia key fob is unable to respond to pressing the lock or unlock button, it's likely that the battery is not fully charged. A battery that is not functioning properly can cause other issues, like the check engine light appearing or the engine not turning correctly. It is fairly easy to replace key fob batteries using just a few simple tools. Make sure you turn off your vehicle and shut all doors prior to starting. Find the small metal or a plastic piece at the bottom of the key fob. Press it until the key is released. You can then insert the key into the handle of the door for the driver to open your car. To replace the key fob's battery, take off the rear cover and use a plastic bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery and orient the new one to ensure that the “+” positive side faces you and the “negative” negative side is facing towards the fob's electrical contacts made of metal. Push the new CR2032 battery straight into position, avoiding excessive force to avoid bending or damaging the contacts made of metal. After key fob replacement kia have installed the new battery then turn the key fob off and on in the ignition until the door locks cycle. You can then test the Kia's key fob again to confirm that it is working correctly. How do you replace a smart keys There is a possibility of having the standard keyfob or Smart Key based upon the model of Kia Sportage. The smart key comes with an embedded mechanical key blade while the standard key fob does not. Both key fobs contain an internal battery that will eventually require replacement. Fortunately, this is a fairly simple process that will take about two minutes. Be sure to switch off your Kia, and be on a flat and well-lit surface prior to you begin. Also, keep in mind that there are tiny pieces inside the fob that could be removed if not careful. The release button for the small size is located on the lower backside. This will either be an oval silver button or a rectangular slot. After pressing this button button, the mechanical blade will pop out and you can then open the key fob. Once you have the key fob open, you can simply remove the old battery, and replace it. The new battery is a CR-2032 that can be bought online or from your local auto parts store. After installation with the battery, you should be able to lock or unlock your vehicle using your key fob – even if the engine isn't running! How do I replace a mechanical key The Kia keyfob can be a fantastic convenience that allows us to lock or unlock our car by simply pressing one button. Like any device like a key fob, the Kia can have issues at times. Luckily, there are steps that can be taken to solve these issues and ensure that our key fobs are in good working condition in the long run. A low or dead battery is one of the most common issues. This can cause the device to cease working or stop working at times. If this is the case try replacing the battery with a fresh new one. If this does not resolve the problem, use the flathead screwdriver that is standard to push the fob's casing made of plastic open. Be careful not to scratch any internal components or scratch the plastic. After opening, carefully remove the old battery and replace it with a new one. Once the new battery is in, close and open the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that can fit into the slot). Test the key fob to confirm it's functioning properly. Contact a dealer locksmith to address the issue if the fob is still not working. Make sure they make you an emergency key that works for all trunk and door cylinders in order to avoid lockouts in the future.